WLAN Antennas 2.4GHz
Directional antennas for outdoor use

On this page you will find:

• Flat panel antennas
• Housing for AP with one or two 2.4G antennas
• Wifi Outdoor antennas with router box
• Helix antennas
• Wifi solid Grid Dish 2.4
• WLAN Prime Focus Parabolic dishes
• Yagi antennas
• Directional antenna, 8dBi
• WiFi antenna 2400 MHz with suction cup holder
• Sector antennas

Antennas with directional capabilities suitable for outdoor use.
Usage: To cover longer sictances from building to building. Usually directional antennas are used on both sides of the link. In some cases it might be sufficient to use a directional on one side only and use the original euqipment antenna on the other side.

Flat panel antennas

PA-13R	PA-13R DUAL	PA-13R18	PA-13R-20
Flat panel antennas consist of one or more radiators placed in front of a reflecting backside. With this principle short, robust and unobtrusive antennas can be designed, which have a high gain and a high bandwidth. Our flat panel antennas are made from weatherproof aluminum, all other hardware is stainless steel. The antennas can be mounted with either horizontal or vertical polarization, all mounting hardware for mast mount is included. The radome protects the antenna system against adverse weather like rain, hail or snow. The model PA-13Dual (18033.DUAL) is an antenna with two system, intended for 802.11n (MIMO) applications.

PA-13R-18 with included pan/tilt mount

PA-13R20 with optional tiltmount)

Suitable cables for PA-13Rxx antennas

Housing for AP with one or two 2.4G antennas

PRG-2400

The PRG-2400 is a flat panel wireless LAN antenna (2.4GHz) with an empty housing. This box is ideally suited for intergation of an accesspoint our WiFi router. Due to the short cable length to the antenna the attenuation is minimal. The external connection is done with an RJ45 ethernet cable, the feed through is protected against water, as well as the box itself of course. So the electronics are always perfectly protected.
The housing PRG-2400 is an ideal solution for the setup of WiFi hotspots or point-to-point links, where the required cable length to an external antenna is too long. The inner size of the box is sufficient to install mostly any AP or router, the PCB is mounted to the solid metal backplane. The power supply is done with power-over-ethernet (POE). The antenna comes with special connector inside, an optional pigtail (18815.xx) is required, available with RP-SMA or RP-TNC connector.

PRG-2400-12: Stainless mounting hardware is included for mast or wall mounting, the mounting allows pan and tilt.
PRG-2400-18: Stainless mounting hardware is included for mast mounting, the mounting allows pan and tilt. For wall mounts a separate wall holder needs to be ordered.

• Flat panel antenna with 12dBi gain
• Weatherproof ABS housing
• Housing and cable feed through splash-proof
• Mounting bracket also suitable for wall mounting

Cable feed through internally, 2x RJ45 jack

Inner view, rear of antenna with cable

PRG-2400 Dual

As a variant this housing is also available with an additional N jack on top. Here an omni directional antenna can be installed, proving all antennas for a very compact hotspot solution. The directional panel antenna provides the connection to the backbone, the omni supplies the local clients.
Suitable omni antennas by WiMo are VC-2400 or MG-200.

Instead of an omni antenna a directional antenna could be connected to the N jack, allowing for a compact repeater system for longer distances.

PRG-2400 "Dual" with N jack for omni antenna

Wifi Outdoor antenna with router box

Bridgepoynt (18790)

The "Bridgepoynt" is a flat panel wireless LAN antenna (2.4 or 5 GHz) with a weatherproof empty housing. This box is ideally suited for intergation of an accesspoint our WiFi router. Due to the short cable length to the antenna the attenuation is minimal. The external connection is done with an RJ45 ethernet cable, the feed through is protected against water, as well as the box itself of course (class IP65). So the electronics are always perfectly protected.
The Bridgepoynt housing 2400 is an ideal solution for the setup of WiFi hotspots or point-to-point links, where the required cable length to an external antenna is too long. The inner size of the box is sufficient to install mostly any AP or router, the PCB is mounted to the solid metal backplane. The power supply is done with power-over-ethernet (POE).

The 5GHz enclosure is now available in a dual polarity version. Integrated into the enclosure are two antennas, one with vertical, the other with horizontal polarization. These two differently polarized antennas help systems like 802.11n (MIMO) to achieve a higher transmission rate. Both antennas have the same gain of approx. 18-20dBi ±0.5dB. The mutual isolation between the antennas is better than 35dB.

18790 Mounting bracket

Techn. Data:

Wifi Outdoor antenna with router box 15/18dBi 'iPoynt'

iPoynt (18792.xx)

A little bit smaller and unobtrusive, with somewhat less gain than it's larger brother (see above). But sufficient for most CPE applications - still 15dBi gain on 2.4GHz and 18dBi on 5GHz.
The new 'iPoynt' antennas have a weatherproof RJ-45 connector, no need to open the case for connecting the cable. Includes a universal swivel and tilt mount for mast or wall mounting. The bottom side of the antenna offers space for installation of additional N-sockets for more external antennas (needs holes to be drilled).

Techn. Data:

Swivel and tilt mount

18792.xx iPoynt Internally

Wifi Outdoor Antenna with Router Box 8/12dBi 'MicroPoynt'

18794.x

This antenna and enclosure is specifically designed to fit MikroTik´s RB 411 router boards.

The antenna comes with an IPEX (U.FL) connector to directly attach to the electronics (not provided). A window allows to inspect the control LEDs without opening the enclosure. The enclosure passes IP67 and is UV stable to ensure longevity of enclosure and electronics. It further features a IP67/NEMA 4P waterproof RJ45 connector, allowing a preassembled Ethernet cable to be installed without opening the enclosure. The antenna can be turned left or right or be turned around for window mount with suckers.

The included mounting bracket allow mountin on a wall or mast or on a smooth surface with suckers. Included in shipment are pegs, screws, a mast clamp and suckers.

Included in shipment is: Antenna enclosure with antenna and cable, mounting bracket, 4 pegs, 4 screws, 4 suckers, mast clamp (max mast diameter 40mm, but with any other clamp larger diameter possible).

Helix antennas

Helix antennas are directional antennas for circular polarization mainly developed for satellite communications but just as well usable for terrestrial operations. Due to physics based reasons the circular polarization shows significant advantages when the received signal may consist of a mix of all kinds of polarizations due to heavy reflections. As an example: If the phase of a received signal is perpendicular to the antenna plane the resulting signal level can be up to 18 dB down compared to a normal yagi! The right-hand circular polarization originates from a helix - the antenna radiates into the direction of the helix. The reflector directs the electromagnetic energy forward; to decrease the antenna's wind load the reflector is perforated (many small holes). All antennas shown here are designed for fore-mast installation. By means of power splitters the helix antennas can be combined to form antenna groups of 2 or 4. The antennas have a standard N-connector and are made of non- corrosive aluminum material with all nuts and bolts made of stainless steel.

Suitable cables for Helix antennas

Wifi solid Grid Dish 2.4

18685.x

The Wifi grid dishes are made from casted aluminium and combine a high stability and low wind load for a long endurance of the antennas. The carefully designed parabolic dish offer a gain of 26dBi on 2.4GHz and 31dBi on 5GHz. In contrast to other parabolic dishes these antennas are designed for best performance also on 5GHz.
Due to the split construction of the reflector (90x70cm) the shipping size is very small, very facorable for the shipping ost. A tilt/swivel mount for mast mounting is included. Connector N female.

Technical data

WLAN Prime Focus Parabolic dishes

Proferssional prime focus dished with 45 or 60cm diameter (18 or 21dBi gain). Solid and weatherproof finish. All required mounting hardware (stainless steel) included, connector N female. In contrast to the dish mentioned above these dishes have a linear polarization. This is beneficial in situations where tightly spaced links have to be separated by polarization, attentuation between links can be up to 25dB with different polarization. The radiators can be mounted in 45° steps in respect to the polarization angle.

SP-60/24 HD (18664)

The Heavy Duty dish SP-60/24 HD is intended for extreme weather conditions. It has a very solid truss bearing, the front is covered by a radome. Weight 10kg.

Suitable cables for Prime Focus dish antennas

Tiltmount for SP45 and SP60 prime focus dishes

Tiltmount to mount the prime focus dishes SP45/xx and SP60/xx to a mast, allows tilt ±45°. Replaces the original bracket. Very solid aluminum construction.

Professional Yagi directional antennas, inkl. swivel/tilt mount, suitable for wall or mast mounting. Completely enclosed, makes these antennas insensible against weather. Connector: cable pigtail with N female jack.

Mounting bracket of YA-2400 Yagis

Suitable cables for Yagi antennas

PA-2408B Directional Patchantenna 8dBi

PA-2408B

Compact and solid patch antenna for 2400MHz Wifi, with 8dBi gain. Suitable for wall or mast mount, including tilt/swivel mount. Intended for use in office areas, cafés, restaurants and other public spaces, where a solid an unobtrusive antenna is required. The antenna is weatherproof and can also be used outdoors. Comes including 20cm cable with N female connector.

FA-2400 WiFi antenna 2400 MHz with suction cup holder

FA-2400

Small patch antenna with 8dBi gain and SMA connector. Comes including a versatile suction cup holder which allows you to mount the antenna on any smooth surface. For example on a window pane - ideal for travellers in a hotel, on conferences or any other temporary locations. The antenna can be rotated on it's arm, covering an angle of at least 180° if necessary, very useful for situations with difficult reception.
The SMA connection is 'in principle' protected against water, still we recommend to use some self amalgating sealing tape for more permanent installations (see WiMo article 23065).

This antenna exists also in a version for UMTS and Wifi 5GHz.

Suitable cables for FA-2400 Antenna

Sector antennas 12, 14 dBi

VP270/24, 12dBi Shown with optional tilt mount	VP470/24, 14dBi
Professional sector antennas for outdoor use. Ideal for coverage of large areas like halls, outdoor areas etc. Horizontal HPBW approx. 70°, connector N jack (female). The directional pattern of these antennas is shaped in a way that the area at the installation point below the antenna is also covered to a certain extent, resulting in a more continous coverage even for antennas mounted in an elevated position.
VP-270/24 Gain: 12dBi HPBW horizontal: 70° HPBW vertical: 27° Polarization: Vertical Size: 95x235x30mm Connector: N jack (female) Mounting hardware for wall or mast mount included Optional tilt mount available Order No. 18640 155.00 € Buy now	VP-470/24 Gain: 14dBi HPBW horizontal: 70° HPBW vertical: 15° Polarization: Vertical Size: 95x470x30mm Connector: N jack (female) Mounting hardware for wall or mast mount included Optional tilt mount available Order No. 18642 205.00 € Buy now
Tilt mount Tilt mount bracket for VP270, suitable for azimuth and elevantion adjustment. Stainless steel, incl. all required hardware. Order No. 18645 Tilt mount VP270 35.00 € Buy now	Tilt mount Tilt mount bracket for VP470, suitable for azimuth and elevantion adjustment. Stainless steel, incl. all required hardware. Order No. 18646 Tilt mount VP470 69.90 € Buy now
4-Way Mount VP-270/470 4 way mount for four VP-270/VP-470 antennas, for mast installation. Order No. 18648 4 way mount 35.00 € Buy now

Suitable cables for sector antennas

Sector antennas 11 to 17dBi

SA24-xx-xx

Professional sector antennas 2.4GHz for indoor or outdoor use. Used for illumination of large areas like hotspots, halls, yards etc. Horizontal HPBW 90 or 120°, N female connector. The included mounting hardware allows a downtilt of up to 15° (see pictures).
With several of these sector antennas (e.g. 3x 120° or 4x90°) a high performance omni directional antenna can be constructed, allowing to adjust each sector angle individualle. Ideally each of these antennas would be powered by an own AP, but it is also possible to combined several antennas with a power splitter.

Enclosed sector antennas 9 to 16dBi

Enclosed sector antennas 2.4-2.5 GHz for outdoor use.Used for illumination of large areas like hotspots, halls, yards etc. Horizontal HPBW 120°, N female connector. The included mounting hardware allows a downtilt of up to 15° (see pictures).
With several of these sector antennas (e.g. 3x 120° or 4x90°) a high performance omni directional antenna can be constructed, allowing to adjust each sector angle individualle. Ideally each of these antennas would be powered by an own AP, but it is also possible to combined several antennas with a power splitter. Temperature range: -40... +70°.

	SAK-120-9 18675.9	SA24-120-10N 18656.10	SAK-120-14 18675.14	SA-120-14N 18656.14
Gain	9	10	14	14	dBi
HPBW hor.	120	120	120	120	°
HPBW vert.	40	20	15	20	°
Polarisation	Vertikal
Connector	N fem.
Dimensions	254 x 120 x 78	520 x 131 x 70	485 x 210 x 70	1020 x 150 x 110	mm
Weight	800	1350	4500	3300	g

Suitable cables for sector antennas